Hello all! Woke up this morning around 7:30 and walked down to Hardee's for breakfast again. I'm still sitting at the Pilot truck stop in Atlanta on the southeast side of the loop.
My appointment time to pick up my load this morning was at 11:00, but sometimes they're ready early. So I drive over at 9:00 AM and the trailer is loaded and they were getting my paperwork together. It was a Con-Way Freight load consisting of misc smaller loads all put together on one trailer headed to Shreveport, LA to the Con-Way Freight location there. Con-Way Freight handles what's called LTL (lessthan-truck-load). You may have seen the smaller Con-Way trailers running single or doubles. I drive for Con-Way Truckload which handles full 53' trailer orders.
Anyway, so I get my paperwork and review the items. There's like a dozen different orders on here with the total weight of 41,000 lbs. I look at the last order loaded; 7 pallets with a combined weight of 20,000 lbs. I knew right then that this wasn't going to be legal!
I hook up to the trailer and take it around the building to their scales. (all C-W Freight terminals have scales on sight) The weight on the drive axles = 26,400 lbs. The weight on the tandem (trailer) axles = 35,800 lbs!! That's 1400 lbs overweight and about a $160 fine! And the axles are already slid all the way to the back! So I had to haul the trailer back around to the dock where they had to either re-load the trailer putting the heavier pallets in the middle or remove some off the tail end. They elected to just remove one of those 7 pallets off the back. DARN! That's what I'd figure they'd do because it's easier and quicker. But it also means that I have to drive with the tandems ALL the way to the rear. Which means EXTRA-WIDE turns! Oh well.
But first, I drive a couple miles in the opposite direction back to that Pilot to get a more accurate CAT scale weight. The Con-Way scales don't get calibrated as often and are not always correct. Plus going to the Pilot's CAT scales will give me a printed copy in case I get stuck at a weigh station.
So, now I'm off around the I-285 loop over to I-20 westbound. My first stop was in Flowood, MS for fuel. Back on I-20 westbound, I arrived in Shreveport, LA at 9:30 PM. I dropped the trailer at the Con-Way Freight there and hooked up to an empty. It's a mess inside and needs to be swept out, but I'm too hungry to do it tonight. A mile back to the I-20 exit where there was a Petro truck stop. Petro's restaurant is called the Iron Skillet because the use small iron skillets instead of plates. I order up a bacon cheese burger, fries, and a sweet tea.
Now it's time for bed. We're headed to San Antonio tomorrow, so I hope you can return to join me. Till then, see ya on the road...
My appointment time to pick up my load this morning was at 11:00, but sometimes they're ready early. So I drive over at 9:00 AM and the trailer is loaded and they were getting my paperwork together. It was a Con-Way Freight load consisting of misc smaller loads all put together on one trailer headed to Shreveport, LA to the Con-Way Freight location there. Con-Way Freight handles what's called LTL (lessthan-truck-load). You may have seen the smaller Con-Way trailers running single or doubles. I drive for Con-Way Truckload which handles full 53' trailer orders.
Anyway, so I get my paperwork and review the items. There's like a dozen different orders on here with the total weight of 41,000 lbs. I look at the last order loaded; 7 pallets with a combined weight of 20,000 lbs. I knew right then that this wasn't going to be legal!
I hook up to the trailer and take it around the building to their scales. (all C-W Freight terminals have scales on sight) The weight on the drive axles = 26,400 lbs. The weight on the tandem (trailer) axles = 35,800 lbs!! That's 1400 lbs overweight and about a $160 fine! And the axles are already slid all the way to the back! So I had to haul the trailer back around to the dock where they had to either re-load the trailer putting the heavier pallets in the middle or remove some off the tail end. They elected to just remove one of those 7 pallets off the back. DARN! That's what I'd figure they'd do because it's easier and quicker. But it also means that I have to drive with the tandems ALL the way to the rear. Which means EXTRA-WIDE turns! Oh well.
But first, I drive a couple miles in the opposite direction back to that Pilot to get a more accurate CAT scale weight. The Con-Way scales don't get calibrated as often and are not always correct. Plus going to the Pilot's CAT scales will give me a printed copy in case I get stuck at a weigh station.
So, now I'm off around the I-285 loop over to I-20 westbound. My first stop was in Flowood, MS for fuel. Back on I-20 westbound, I arrived in Shreveport, LA at 9:30 PM. I dropped the trailer at the Con-Way Freight there and hooked up to an empty. It's a mess inside and needs to be swept out, but I'm too hungry to do it tonight. A mile back to the I-20 exit where there was a Petro truck stop. Petro's restaurant is called the Iron Skillet because the use small iron skillets instead of plates. I order up a bacon cheese burger, fries, and a sweet tea.
Now it's time for bed. We're headed to San Antonio tomorrow, so I hope you can return to join me. Till then, see ya on the road...
